by fevold 18 Nov 2010

arrrrggg! My machine hates metalic thread. I tried to do some FSL in metalic and it kept breaking threads and needles. It's not the designs because they stitch out great in reg. thread uggg.

1177

by mariahail 18 Nov 2010

99.5% of machines hate metalic thread, LOL *****

60484
by ramona 18 Nov 2010

All the things these girls have mention and then something else I've heard is that when purchasing metalic thread take a minute and unwind about 12 - 15 inches. Let it hang down and then grab the end and pull it back up to the spool. If it hangs straight and does not spiral back on itself, it should be easier to work with.

23222
by lbrow 18 Nov 2010

Do as Bikermom tells you. Me I put the thread stand as far away from the machine as possible but still where ican see it. the problem with most metallics is they will kink either just before feeding into machine or after they are in channel in machine this causes the breaking of thread & needles. the packing peanut or small piece of styrofoam is a Godsend.

145791
by shirlener88 18 Nov 2010

I think all the TIPS I would have shared with you - have been covered - happy stitiching.

211079
by bevintex 18 Nov 2010

watch this short video for a tip on using a packing peanut and some other solutions.

1 comment
shirlener88 by shirlener88 18 Nov 2010

D Jones is always a good source.

67271
by kttyhwk4 18 Nov 2010

Follow the advice of bikermomfl as this is how I do it also and so far no problems at all. GOOD LUCK!

20661
by bettyboop13 18 Nov 2010

The only other suggestion I have is use the Net that came with your machine. Put it around the thread

1 comment
shirlener88 by shirlener88 18 Nov 2010

a must!

1774
by feedabear 18 Nov 2010

I double thread with a clear thread and the metallic - this has worked for me. Don't have a clue what the brand of this thread is at the moment since I'm not home in my sewing room for a few more weeks.

1144
by anangel 18 Nov 2010

The metallic thread has given me more frustration than any other type, but I found it helped tremendously to place the spool upright on a thread holder placed directly behind my machine in line with the main thread slot of the machine. The thread being pulled gently from this spool holder alleviated a lot of the twisting of the metallic thread which causes the thread to break. The single spool threadholder I purchased at Hancocks for 9.99 has been worth a fortune to me!

I haven't tried any FSL, so do not know if they are dense designs or not. Density could cause metallic thread to give you problems.

Maybe someone else will come along to help you more.
Don't give up yet!!
Angel

12500
by bikermomfl 18 Nov 2010

now now now, we all have our metallic thread problems. The best advice I've found for my particular machine is: 1) slow the machine way down; 2) Move the thread away from the machine on a seperate thread stand if you have it; 3) Bypass the first tension disk when threading your machine, if possible; 3) Always use a metalic thread needle it has a larger eye; and finally 4) cross your fingers, hold your breath, say little prayers and hope! *giggle* hope some of this helps it has worked wonders for my machine - husqvarna designer 1

3 comments
fevold by fevold 18 Nov 2010

This sounds like a good one to try.
Thanks

lildoll by lildoll 18 Nov 2010

also put your thread in a cup , not on thespindle, so it can relax , this thread tends to twist, never had a problem, good luck

katydid by katydid 18 Nov 2010

very good , I agree 100%.

17161
by sewdoctor 18 Nov 2010

this was addressed in by another cutie...go here and read! It will help!

1 comment
fevold by fevold 18 Nov 2010

wow, can't wait to try some of those. I'd heard of the freezer trick, but had completely forgotten. Thanks so much for your link.
Laura

40397