can someone please help me with this free design,I can not get it to load onto my machine ,is shows up on my usb stick , but when I load it into my 11000, it tell me it is damaged ,and asks if I want to delete it.

HI Monika it comes up as a dangerous page when I try to get it.

I have found this with my Janome. I downloaded the design in a differnet format, and then convert it to Jef. This usually works for me. I have the 300E.

I downloaded the zip file and didn't have any trouble opening up the design. The only thing that I noticed right away was that there isn't a JEF format. Could that be the problem?

When you resize did you save it first and then load it on the usb and tried it again? I did it when I first started and resize a design and send it to my machine and then it doesn't show until I realized I must resize save it close it and then send it via USB then it will show on my machines screen. Hope this help. Hugs Louise

OK, well according to Embird the size for your hoop should be 7.87 x 7.87 maximum. If you try this size it should work for you. Let me know how it goes.
Hugs n love, Meg

1 comment

by aussiequilter 22 Feb 2012

Thank Meg ,I will give it a try,,,,7.87

Monica I have just downloaded these designs and will have a look at them for you. Jef is your format isn't it?
Hugs, Meg
Do you have my phone number?

My MalewareBites and Norton are blocking me from this site, so be careful the site might have a bug in it.

2 comments

by aussiequilter 22 Feb 2012

my virus protection normally blocks me if its sus , it did let me download it. it just wont show up on my machine

by edithfarminer 22 Feb 2012

I have Norton and no problem for me

Wow, Monica this is a really beautiful design. Do you have the 11x7 hoop because if you do you can do it in that? I saved it in my Husqvarna Designer 1 under the 11x7 (150x240) and I had no troubles. I think you could decrease it a little I have a resize option on my machine and I just tried it in the 7x5 hoop (13x180) and it reduced the stitches down to 57955 instead of 79,000 in the large hoop. Love Chris

1 comment

by aussiequilter 22 Feb 2012

Chris ,I resized it to fit the 6 x8 hoop,it still wont show up ,I did give the Iris a try, and it did all sorts of weird things,I will have to just try to work out another option for the challange

I did reduce the design to fit my 200 x 200 hoop,I took it to 7.9" what am I doing wrong ?????

2 comments

by caroldann 21 Feb 2012

Monica, I just resized to 123.1 X 199.8. Put it on my usb stick, took it to the machine and there it was. We have the same machine and I just can't figure out what you're doing wrong. Hugs..Carol

by aussiequilter 22 Feb 2012

I dont know what Im doing wrong either!!!!!!

I went and dl this design. The size is 131.9 X 218.8 mm or 5.19 X 8.61. Unless you have a hoop big enough this is too large for your machine. I have the MC11000SE and this would not fit my 8 X 8 hoop. It will show up on your stick but it isn't going to load in your machine. You could try resizing it and see what happens. Hope this helps. Hugs..Carol

thank you

wow, it is very pretty. PE Design (Brother) says it has 77,655 stitches. My Brother picked it up ok but it tells me it will take 165minutes (2&3/4 hours)to sew at 800spm. Try downloading it in a differnt format??? xx

I have found on my machine that when this happens. I have a larger size design than my machine will do. Or it is a different format. But in either one of these cases it always shows up on the flash drive. Good luck.